The official post whore thread..
03-14-2009, 11:19 AM
#7704
Ruff Ryder
Join Date: Sep 2005
Location: palm desert
Posts: 6,140
03-14-2009, 01:25 PM
#7705
Über User
Join Date: Sep 2005
Location: lemont, Illinois
Posts: 9,532
i enjoy manual, but i bet gas mileage is completely horrible. lol, damn carbs!
also, i cant afford **** now cause i went into my garage at 1:30 to go take a nice ride on the kawi, and the tire is flat, since i dont have any bike stands i had to take it in and with tire and now labor mount and balance i have to pay 259 dollars.... i just sold my fish tank for 350. im pretty sad right now. and they were freaking pirelli diablo rosso's with only like 3k miles on them! my local shop only had dunlop's cause they are a yamaha dealer
also, i cant afford **** now cause i went into my garage at 1:30 to go take a nice ride on the kawi, and the tire is flat, since i dont have any bike stands i had to take it in and with tire and now labor mount and balance i have to pay 259 dollars.... i just sold my fish tank for 350. im pretty sad right now. and they were freaking pirelli diablo rosso's with only like 3k miles on them! my local shop only had dunlop's cause they are a yamaha dealer
03-15-2009, 10:54 AM
#7708
Ruff Ryder
Join Date: Sep 2005
Location: palm desert
Posts: 6,140
found some interesting info on those vinyl top z's http://bringatrailer.com/2009/01/07/...1-datsun-240z/ read the comments.
03-15-2009, 03:43 PM
#7714
Haterade by da gallon!
Join Date: Jun 2008
Location: Valdosta GA
Posts: 2,306
yeah im the one on the left 
how is that wigger? its just not redneck like
btw i got that hat from my grandpa (rip) and it came that way
oh and that hat has been signed by ashley force/hood TWICE!!!
how is that wigger? its just not redneck likebtw i got that hat from my grandpa (rip) and it came that way
oh and that hat has been signed by ashley force/hood TWICE!!!
03-18-2009, 11:18 PM
#7721
NisTuner
Join Date: Sep 2005
Location: Cleveland, Ohio
Posts: 2,800
Well I was productive today. I went out and changed out my CHTS on my Z31. Not too hard when you follow the Z31.com repair writeup. Still a pain in the *** though. Also replaced the hood switch for the security system. Put in a new sub harness for the CHTS as well. Now I need to go get silicone sealant to seal the cracks around the T-Top drain tubes and then I should be good.
03-19-2009, 05:09 PM
#7722
Haterade by da gallon!
Join Date: Jun 2008
Location: Valdosta GA
Posts: 2,306
Hobart Handler 125 EZ Welder
is it good for anything in the automotive direction? i can get it for $300, i hate to ask but im not in an ag mechanics class right now to get any info from the experts, so i turn to
yall
http://www.hobartwelders.com/product.../handler125ez/
The Handler 125 EZ has Hobart’s unique Single-**** Control making it the quickest and easiest wire welder to set up and use. Just plug it into 115 VAC, select the mild steel thickness with the Single **** Control and you are ready to weld. The Handler 125 EZ comes ready to weld 18 gauge–3/16 in mild steel with .030 in (0.8 mm) self-shielding flux-cored wire so no shielding gas bottle is required. Also designed to use .035 in (0.9 mm) flux cored wire with a .035 in (0.9 mm) contact tip.
Comes complete with:
*Comfortable H-9A gun, 8 ft. (2.4 m)
*Spare .030 in (0.8 mm) contact tips
*10 ft. (3 m) work cable with clamp
*Sample spool of .030 in. (0.8 mm) self-shielded flux cored welding wire
*Spool shaft to accommodate 4 in spools (Optional hub kit available for 8 in spools)
*Power cord with plug
*Weld set-up and parts information chart [PDF]
*Owner's manual with parts lists, installation, operation, and maintenance guidelines
Power: CV DC 1 Phase
Processes: Flux Cored [FCAW]
Material Thickness: Welds 18 gauge up to 3/16 inch
Skill Level: Low
Applications: Farm/Ranch, Light Maintenance and Repair, Light Fabrication
yall
http://www.hobartwelders.com/product.../handler125ez/
The Handler 125 EZ has Hobart’s unique Single-**** Control making it the quickest and easiest wire welder to set up and use. Just plug it into 115 VAC, select the mild steel thickness with the Single **** Control and you are ready to weld. The Handler 125 EZ comes ready to weld 18 gauge–3/16 in mild steel with .030 in (0.8 mm) self-shielding flux-cored wire so no shielding gas bottle is required. Also designed to use .035 in (0.9 mm) flux cored wire with a .035 in (0.9 mm) contact tip.
Comes complete with:
*Comfortable H-9A gun, 8 ft. (2.4 m)
*Spare .030 in (0.8 mm) contact tips
*10 ft. (3 m) work cable with clamp
*Sample spool of .030 in. (0.8 mm) self-shielded flux cored welding wire
*Spool shaft to accommodate 4 in spools (Optional hub kit available for 8 in spools)
*Power cord with plug
*Weld set-up and parts information chart [PDF]
*Owner's manual with parts lists, installation, operation, and maintenance guidelines
Power: CV DC 1 Phase
Processes: Flux Cored [FCAW]
Material Thickness: Welds 18 gauge up to 3/16 inch
Skill Level: Low
Applications: Farm/Ranch, Light Maintenance and Repair, Light Fabrication
03-19-2009, 05:13 PM
#7723
Pr0n Addict
Join Date: Sep 2007
Location: virginia
Posts: 4,617
is it good for anything in the automotive direction?
"Applications: Farm/Ranch, Light Maintenance and Repair, Light Fabrication "
"Material Thickness: Welds 18 gauge up to 3/16 inch "
look! i/you answered your question!
"Applications: Farm/Ranch, Light Maintenance and Repair, Light Fabrication "
"Material Thickness: Welds 18 gauge up to 3/16 inch "
look! i/you answered your question!
03-19-2009, 05:18 PM
#7725
Haterade by da gallon!
Join Date: Jun 2008
Location: Valdosta GA
Posts: 2,306
